How to fill a pool with dirt

How much does it cost to fill a pool with dirt?

Cost To Fill In A Pool With Dirt

The average cost to fill in a swimming pool with dirt is $1,000 to $6,000, including delivery, labor, compacted fill dirt, and topsoil. Structural fill dirt costs $10 to $30 per cubic yard, depending on the amount needed.

How much dirt is needed to fill in a pool?

For example if our pool is 30′ long, 20′ wide’ and 6′ deep, it has a total volume of 3,600 square feet (30x20x6). The total square footage divided by 27 is 133.33, this indicates that your pool will need 133.33 cubic yards of material to fill it in.

How do I fill my inground pool?

How to Refill and Drain an Inground Pool

  1. Step 1 – Rent a Sump Pump. Go to your local equipment rental store and rent a sump pump that is submersible. …
  2. Step 2 – Lower the Sump Pump in the Pool. …
  3. Step 3 – Clean the Pool Sides. …
  4. Step 4 – Remove the Pump. …
  5. Step 5 – Refill the Pool. …
  6. Step 6 – Add Chemicals.

What chemicals do I add to fill my pool?

Startup Chemicals to Open Your Pool

  • Optional Anti-scaling Product. If you’re filling your pool with fresh water, this is a good time to add an anti-stain or anti-scaling product. …
  • Adjust the pH. …
  • Adjust Total Alkalinity. …
  • Sanitize the Water. …
  • Adjust Hardness. …
  • Add Algaecide.

Can I just fill my pool with dirt?

Option 1: Filling in a pool (partial removal)

Filling in a pool involves draining the pool, punching holes in the bottom, demolishing the top layer of the pool (18″ – 36″), placing the rubble in the bottom, filling in the pool with additional dirt and topsoil, and compacting the soil.

You might be interested:  How much does a radiant pool cost

Do fire departments fill pools?

USING WATER FROM THE FIRE DEPARTMENT

It used to be common enough for fire departments to fill swimming pools, but these days you’re quite lucky if you’re able to pull off a request. This could be less expensive than some of the alternatives as some departments will fill your pool or hot tub in exchange for a donation.

How do you calculate dirt fill?

Length in feet x Width in feet x Depth in feet (inches divided by 12). Take the total and divide by 27 (the amount of cubic feet in a yard). The final figure will be the estimated amount of cubic yards required.

How much does it cost to fill a 1000 gallon pool?

It costs between $4 and $10 per 1000 gallons of water on average that is used in your home. When it comes to filling a swimming pool after installation, it could take just a few thousand to over 20,0000 gallons of water depending on your pool size.

How much dirt is there in a hole 3 feet deep 6 ft long and 4ft wide?

A hole in the ground of 3 ft X 4 ft X 6 ft = 72 cubic feet. 72 cubic feet divided by 27 cubic foot per cubic yard = 2.6667 cubic Yards X +/- 4,000 pounds per cubic yard = 10,666.6667 pounds of dirt to move. 10,666.6667 pounds divided by 2,000 pounds per ton. This equates to 5.333 tons of dirt to haul off.

How often should you add water to a pool?

For a normal sized pool you will loose 25,000 to 50,000 gallons of water per year due to evaporation. This means I was putting a hose in the pool every 7-10 days to fill the pool.

You might be interested:  How to care for a salt water pool

Should I drain my pool to get rid of algae?

DON’T DRAIN IT!

Depending on factors like water temperature, the amount of solids in the pool, and the capabilities of your pool filter system, the process can take 3 days or 3 weeks. Start up the Filter – Without a properly working filter, the water will never clear.

Should I drain my inground pool to clean it?

Even with proper and regular pool maintenance, it’s often necessary to drain your pool — completely or partially — every 3-5 years. Draining your pool often isn’t necessary, especially if you’re following a proper and regular pool maintenance program.

What chemicals do I add first to my pool?

First, balance total alkalinity because it’s like an umbrella measurement that can help protect pool conditions and keep chemicals levels in check. Raise total alkalinity with baking soda or soda ash and lower total alkalinity with muriatic acid.

How soon after filling a pool Can you swim?

Do not swim in the pool until after the start-up procedure has been completed. Do not use any automatic pool cleaners for a minimum of three weeks after plastering.

Leave a Reply

Your email address will not be published. Required fields are marked *