How to open swimming pool after winter

What chemicals do I need to open my pool?

Chemicals Checklist: Everything You Need to Open Your Pool

  • A good test kit or test strips for checking your pool’s pH, calcium hardness, total alkalinity, and chlorine levels.
  • Chlorine granules or tablets.
  • Shock treatment.
  • Increaser/decreaser chemicals for alkalinity, calcium, and pH.
  • Algaecide.
  • Stain treatment.

How do I open my pool for the season?

Steps for opening your pool:

  1. Drain and Clean the Pool Cover. …
  2. Remove the Pool Cover. …
  3. Clean and Store the Pool Cover. …
  4. Raise the Water Level Back to Normal. …
  5. Reconnect the Pool Equipment. …
  6. Remove Winterizing Plugs from Skimmer and Return Lines. …
  7. Turn the System Back On. …
  8. Add MetalFree to Prevent Staining.

What chemicals do I need to start up my above ground pool?

  • Stain & Scale Preventer.
  • Granular Shock Chlorine.
  • Chlorine Tablets.
  • pH Increaser and/or pH Decreaser.
  • Alkalinity and/or Calcium Increaser.
  • Cyanuric Acid (Stabilizer)
  • Algaecide and Clarifiers if needed.
  • Complete Test Kit or Test Strips.

8 мая 2019 г.

Should I brush pool before shocking?

Before you start pouring shock in the pool, the very first step is to brush the sides and floor of your pool to loosen all the algae. Doing this breaks the ‘skin’, and allows the pool shock to more easily kill the algae. Once you’ve done this, it is important to make sure you have the proper pH level in your water.9 мая 2014 г.

How many bags of shock do I need to open my pool?

To shock your pool, use 2 pounds of shock for every 10,000 gallons of water, which should raise your chlorine to 10.0 ppm. Depending on your pool, you can use Leslie’s Power Powder Plus or Leslie’s Chlor Brite. After shocking the pool, run the circulation system for at least 2 hours before adding an algaecide.25 мая 2017 г.

You might be interested:  How to hook up pool vacuum to skimmer

How do you close an inground pool?

Closing an In Ground Pool for the Winter

  1. Step 1) Get your equipment organized. …
  2. Step 2) Prepare the pool. …
  3. Step 3) Prepare filters and pumps. …
  4. Step 4) Prepare your pool heater (if applicable) …
  5. Step 5) Drain and blow out your lines.
  6. Step 6) Plug the skimmer hole. …
  7. Step 7) Balance your chemicals. …
  8. Step 8) Install your pool cover.

Do I need to shock a new pool?

Every pool is different, and pools don’t need to be shocked, unless they need to be shocked – to remove bacteria, algae, chloramines or other contaminants, or to help clear cloudy pool water or some other water problem. You can test for chloramines and you can see algae, but bacteria and other pathogens are invisible.

What to do after filling a pool?

Test your water immediately after refilling to balance and add start-up chemicals. You can also take a water sample into a Leslie’s store for testing. Leslie’s will test your water and provide the results with a prescription for improving your water quality.

Is shock and chlorine the same thing?

Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly. Chlorine tabs (placed in a chlorinator, floater, or skimmer basket) maintain a chlorine residual in the water. You do need to use both tabs and shock. … You should aim to keep the chlorine level at between 1 and 3 ppm.

Should I shock my pool when I first fill it up?

At first you’ll add chlorine in what’s called “shock” levels – an extra heavy dose to start your pool off. A shock dose coupled with extra circulation will ensure that all the water gets treated properly in the beginning.17 мая 2018 г.

You might be interested:  How to set up intex pool

Do I use shock or algaecide first?

Algaecide should be used after each shock treatment, so it has a better chance to support your chlorine as it works its magic. Be sure to shock your pool first, then when the chlorine levels of your pool return to normal, add the correct amount of algaecide to several places around your pool while your pump is running.

How do you ruin a pool?

Here are six common ways that pool owners damage their pools.

  1. Tearing the Pool Liner. …
  2. Not “Winterizing” the Pool or Spa Properly. …
  3. Not Maintaining Proper Ph and Alkalinity. …
  4. Not Brushing the Sides. …
  5. Adding Shock Directly Into the Filter. …
  6. Adding Shock Directly to the Water.

What happens if you put too much shock in your pool?

Although, if you overdo the shock treatment, you risk getting green hair from chlorine due to the excess chlorine oxidizing the copper in the water. You can execute a shock treatment with a few different types of pool shock, just be mindful of how much you’re using.

Leave a Reply

Your email address will not be published. Required fields are marked *