What chemicals do you need for a pool

What chemicals do you need to maintain a pool?

How To Maintain A Swimming Pool Part 1 (Chemicals)

  • Chlorine- This is your primary sanitizer. …
  • Bromine- Bromine is an alternative to chlorine. …
  • pH- This is a measure of the water’s total acid-alkalinity balance. …
  • Shock- This is another type of chlorine. …
  • Alkalinity- Also referred to as total alkalinity is a measure of alkaline in the water.

What chemicals do I add first to my pool?

Startup Chemicals to Open Your Pool

  • Optional Anti-scaling Product. If you’re filling your pool with fresh water, this is a good time to add an anti-stain or anti-scaling product. …
  • Adjust the pH. …
  • Adjust Total Alkalinity. …
  • Sanitize the Water. …
  • Adjust Hardness. …
  • Add Algaecide.

How do I treat my pool for the first time?

Filling your new pool for the first time?

  1. Place the garden hose in the deep end of the pool, making sure to tie a cloth over the end of the hose to diffuse the water pressure. …
  2. Test and correct the pH level to 7.2 – 7.6.
  3. In the early evening, add 2 cups of HTH® Granular for every 10 000 liters of pool water. …
  4. Filter continuously for 24 hours.

What happens if you put too much chlorine in your pool?

Having too much chlorine in your pool water can be dangerous. Exposure to high levels of chlorine can cause lung irritation, skin and eye damage, and provoke asthma. … High chlorine levels decrease the pH of your pool’s water, making it more acidic. The more acidic the water, the higher the likelihood of corrosion.

You might be interested:  What size pump for above ground pool

How do I keep my pool crystal clear?

So the best way to have a crystal clear pool is prevention.

  1. Keep the chemical levels within the ideal ranges.
  2. Check the flow meter to be sure the pool is circulating water at a proper flow rate.
  3. Brush the walls and floor weekly.
  4. Keep a preventative amount of algaecide in the pool.

How soon after filling a pool Can you swim?

Do not swim in the pool until after the start-up procedure has been completed. Do not use any automatic pool cleaners for a minimum of three weeks after plastering.

What pool chemicals should not be mixed?

Most common swimming pool chemicals are incompatible with each other and should never be mixed. Mixing of organic chlorinating agents (such as trichloroisocyanuric acid) and inorganic chlorinating agents (such as sodium hypochlorite) can lead to fires, explosions and chlorine gas release.

Do I need to shock my pool when I first fill it?

At first you’ll add chlorine in what’s called “shock” levels – an extra heavy dose to start your pool off. A shock dose coupled with extra circulation will ensure that all the water gets treated properly in the beginning.17 мая 2018 г.

Can I just throw chlorine tablets in my pool?

Chlorine tablets are the most commonly used and most efficient sanitizer for pools because of their ease of use. … NEVER just throw them into your pool water. This will cause them to dissolve on the floor and it can damage and create a permanent bleach stain to your liner or concrete.

You might be interested:  What is defined by the ip nat pool command when configuring dynamic nat?

Is it OK to fill a pool overnight?

Hi, with 12″ of water in the pool you should be fine to let it fill all night. The stretching should be done and the liner tight against the wall. If so, let it go. There is some air gap between the liner and the wall in a few areas.

What new pool owners should know?

37 Things new pool owners must know!

  • If you drain your pool, it can “pop” out of the ground by floating on the ground water. …
  • Pool water must be tested weekly in order to insure the water is safe to swim in. …
  • Adding chlorine tabs each week without testing the water will result in a pool that is too acidic and has too much stabilizer.

Does too much chlorine make pool cloudy?

An excessive amount of pool chemicals can cause your water to be cloudy. That includes: high pH, high alkalinity, high chlorine or other sanitizers, and high calcium hardness. One of the only ways to immediately know what chemicals you’ve overused in your pool is through the pHin mobile app.

How long does it take for chlorine levels to go down?

24-48 hours

Leave a Reply

Your email address will not be published. Required fields are marked *