What size pool pillow do i need

What size winter pool pillow do I need?

When you close your above ground pool for the winter, you should place an air pillow in the center of the pool before you put on your winter cover.

Inflating Your Air Pillow.Pool SizeSuggested Air Pillow SizeMaximum Air Pillow Size15′ X 26′ Oval4′ X 8’4’X15′ or (2) 4’X8’15’ X 30′ Oval4′ X 8’4′ X 15’Ещё 33 строки

What can I use instead of a pool pillow?

Use an Air Pillow with Your Pool Cover

No problem. Keep your cover free of debris with an air pillow. This turns your flat cover into a dome, ensuring leaves, snow, ice, and debris slide right off. Just make sure to secure the cover first.

Why does my pool pillow keep deflating?

Ice Equalizer pillow has popped or deflated

This just means that the pillow has done its job! The purpose of the pool pillow is to compensate for the rain, snow or ice in your pool and on your cover.

Do you need a pillow under a pool cover?

The first reason to install a winter cover air pillow is to protect your pool from expanding ice. When you don’t use an air pillow, the cover sits right on top of the water and the ice will want to expand outwards. … The air pillow prevents water from pooling in the center of the cover.

Should I empty my above ground pool for the winter?

Important: Never completely drain an above ground pool. This can cause your pool to collapse. If your pool is plumbed with detachable, flexible hoses, remove them and store for the winter. … Basically you’ll need to drain them so there is no water in them that could freeze and damage the pump or filter.

You might be interested:  What is the average cost of a pool

Should pool cover touch water?

Your pool water level should not be too low, as the water must support the cover in situations where you receive a heavy snowfall. At the same time, ideally you don’t want the water to touch the underside of the cover under general conditions as that contact will create a wet spot where debris will accumulate.

How do I keep my pool cover from sagging?

There are a few ways to prevent sagging with an automatic pool cover. The first is to winterize your pool correctly. Make sure the water level is no lower than 18 inches below the pool deck, or halfway up your skimmer opening, as the surface of the pool will help hold up the cover.

How do you use an air pillow?

Begin pumping air into the cells to the point when the pillow is full. D. Quickly remove the tube from the valve and turn the vale clockwise to close it and trap the air inside. E) Now, lie back and place your head on top of the pillow and open the air valve to release the air slowly.

How tight should my pool cover be?

If yours is a mesh cover, it should be almost “taut as a drum”, as the water will drain through it evenly. If yours is a solid cover, either with an automatic cover pump or a porous drain strip, it should be kept slightly less tight in the area of the pump or drain strip.

How many air pillows do I need for my pool?

How Many Air Pillows Do I Need?Pool SizeSuggested Air Pillow Size21′ Round 24′ Round4′ x 8’27’ Round 30′ Round 33′ Round4′ x 15’8′ x 12′ Oval 8′ x 14′ Oval 8′ x 16′ Oval 8′ x 19′ Oval 10′ x 15′ Oval 10′ x 16′ Oval 10′ x 18′ Oval4′ X 5’10’ x 19′ Oval 10′ x 21′ Oval 12′ x 16′ Oval 12′ x 17′ Oval 12′ x 18′ Oval4′ X 5’Ещё 7 строк

You might be interested:  What is a lap pool

Can you use a tarp for a pool cover?

An obvious solution is to cover the pool when it’s not in use to keep out foreign material, but custom-made swimming pool covers can be quite expensive. An alternative option, much less expensive, is to use a large plastic or vinyl tarp, secured at the corners with tent stakes and bungee cords.

Why use an air pillow in a pool?

An air pillow creates an uneven surface on the top of your pool for your winter cover to lay on. This helps prevent any ice damage from precipitation that lands on top of the winter cover and freezes. Use an air pillow to protect your inground or above ground pool during the winter!

How do I fill my pool air pillow?

How to Inflate Air Pillows for Pools

  1. Read the label on the side of the pool pillow. …
  2. Attach the hose of your air compressor to the intake nozzle on the pillow. …
  3. Run the automatic or hand-crank compressor until the pillow is firm to the touch. …
  4. Remove the filler hose from the pillow and immediately seal it with the plug.

Leave a Reply

Your email address will not be published. Required fields are marked *