How to treat swimming pool water

How do you treat new pool water?

Filling your new pool for the first time?

  1. Place the garden hose in the deep end of the pool, making sure to tie a cloth over the end of the hose to diffuse the water pressure. …
  2. Test and correct the pH level to 7.2 – 7.6.
  3. In the early evening, add 2 cups of HTH® Granular for every 10 000 liters of pool water. …
  4. Filter continuously for 24 hours.

What chemicals do you need to start a pool?

Chemicals Checklist: Everything You Need to Open Your Pool

  • A good test kit or test strips for checking your pool’s pH, calcium hardness, total alkalinity, and chlorine levels.
  • Chlorine granules or tablets.
  • Shock treatment.
  • Increaser/decreaser chemicals for alkalinity, calcium, and pH.
  • Algaecide.
  • Stain treatment.

How can I ruin my pool water?

Here are six common ways that pool owners damage their pools.

  1. Tearing the Pool Liner. …
  2. Not “Winterizing” the Pool or Spa Properly. …
  3. Not Maintaining Proper Ph and Alkalinity. …
  4. Not Brushing the Sides. …
  5. Adding Shock Directly Into the Filter. …
  6. Adding Shock Directly to the Water.

How do I disinfect my pool water?

Disinfection methods for swimming pool water

In some countries, sodium hypochlorite is used for both oxidation and disinfection of swimming pools. When it is added to water, sodium hypochlorite increases the pH value. It is better to use chlorine as a disinfectant and an oxidizer at a pH value of 6,5.

How long can pool water sit without chemicals?

24-48 hours

How much baking soda do I add to my pool?

A rule of thumb is 1.5 lbs. of baking soda per 10,000 gallons of water will raise alkalinity by about 10 ppm. If your pool’s pH tested below 7.2, add 3-4 pounds of baking soda. If you’re new to adding pool chemicals, start by adding only one-half or three-fourths of the recommended amount.

You might be interested:  Swimming pool payment plan

Can you put too much chlorine in a pool?

Having too much chlorine in your pool water can be dangerous. Exposure to high levels of chlorine can cause lung irritation, skin and eye damage, and provoke asthma. … High chlorine levels decrease the pH of your pool’s water, making it more acidic.

What to put in pool after filling it?

Add a clarifier to the water. The clarifier will help the filter to remove the very tiny particles that enter the pool in the filling process or that may remain following construction and installation. 5. Start the pump and filtration equipment and allow the water to circulate for 24 hours, if practical.

What do I balance first in my pool?

Step 4 – Shock the Pool!

Equally important is to balance the water first, before shocking a pool. Minerals, metals and dirt often mix and deposit as stains or scale during shocking, when pool water is not balanced. In addition, chlorine has much more power or efficacy at lower pH levels, so you can use less.

How often should I backwash my pool?

As a general rule, you should be backwashing your pool about once a week or in conjugation with your scheduled maintenance. Another industry standard is to backwash when your filter’s pressure gauge reads 8-10 PSI (pounds per square inch) over the starting level or “clean” pressure.

How much chlorine do I need to shock my pool calculator?

A simple ratio and a standard rule of thumb to follow when you shock your pool is to dissolve one pound of either calcium hypochlorite or sodium dichlor for every 10,000 gallons of pool water.

You might be interested:  How to heat a swimming pool

Should I backwash after shocking pool?

Backwash only as needed. Brush the pool vigorously, several times after shocking the pool. Do not use a solar blanket until chlorine and pH level are normal. If chlorine level drops to zero within 24 hours, Repeat the shock treatment.

Can I use pool chlorine as a disinfectant?

Chlorine bleach products can be used to clean drinking water, pools, and countertops. … However, chlorine is an effective household disinfectant when used in a product like chlorinated bleach.

How often should you put chlorine in your pool?

If the pool is used more than 2 days a week, the water quality needs to be checked 2 to 3 times a week. If the pH value is good, check whether the chlorine tablet has completely dissolved or not. Once the chlorine tablet has dissolved, it is best to add 1 chlorine tablet per skimmer.

Leave a Reply

Your email address will not be published. Required fields are marked *